Marten Base 15kw

Quality of coppers of Marten it is reached thanks to a combination of such factors:

MATERIAL, RELIABILITY AND DURABILITY Marten's Coppers are produced from heat-resistant, boiler steel, not exacting to quality of fuel.

• from 3 mm. (Base series) of the Pipe and the water filled, besshevny grid-irons are made of boiler steel of 5 mm
• Brand 09G2S steel is applied - it is steel which in standards of the EU has marking of P265GH.
• Such steel still call boiler, service life in the conditions of high temperatures from 15 to 20 years.

The high-precision equipment, at production.

• To release a large number of quality coppers it is impossible to do without the modern high-performance equipment. By production of coppers it is used such machines: "Fronius" (Austria), "Hiperterm" (USA)," Euromac" (Italy), "Motoman" (Japan).
• In welding works the robot is used that at all solve a leakage problem. (Watch video)

Check

1. All coppers after welding undergo pressure testing - it is operation at which the copper is put under pressure for 10 - 12 hours. If pressure decreased not below standard,
2. Such check guarantees that the copper will arrive to the consumer obviously tight and will not flow.

Final assembly 1. Warming

• on a copper the decorative covering with a heater is established inside

2. Electronics

• In the coppers having electronic control controllers of the Polish company are installed
• N TESN and fans (pressurization turbine) M+M (Poland).

• Coppers of the MartenIndustrialPro series are completed with the most difficult Siemens electronics which operates all systems of a copper.

3. Painting it is always pleasant to take our coppers in hand.

• Coverings are painted by method of powder painting on the modern painting line.

Technical control (Quality Department)

• The final stage before receipt of a copper on a finished goods warehouse is a passing of technical control (Quality Department).
• At the same time more than 20 parameters, according to the card of control are checked.
• At discrepancy at least of one parameter with standard the copper is sent back for revision.

Guarantee

1. 36 months on the equipment the Copper sertefetsirovan

Saving of your time and means.

• In the Base series thanks to the increased heat exchanger consisting of a water shirt, the water filled grid-irons, the massive top water filled shelf and pipes which are slowing most down pass of hot dymogaz to a flue.
• Thanks to such decision we achieved increase in efficiency of the heat exchanger.

Complete set

• With each copper the tool set for service of a copper is delivered

All these actions guarantee that the consumer will receive the copper which is conforming to all requirements and not having factory defects

 

 Solid propellant copper of Marten Base 18kw

Saving of your time and means.
Simplicity in installation.

Solid propellant coppers of the Marten Base series with a power from 15 kW are intended for heating of rooms up to 150 sq.m by main types of fuel: coal, firewood, briquettes.

Main advantages of a copper of Marten Base MB-18

Convenience and Practicality

• Marten Base duration of combustion of single loading of fuel: 4-6 hours. Depending on quality of fuel and warming of the house.
• It is easy to clean a solid propellant copper of Marten Base-. Thanking a protective lattice even if you during burning of a copper of Marten Base want to throw out ashes, the burning coal or firewood will not drop out.
• The capacious cindery box allows you easily will get rid of the ashes which fell under grid-irons.
• Easy management and control of the necessary mode of burning by means of a mechanical temperature regulator
• Also control of burning at the help of the regulator of draft of Marten Base copper located behind.

Reliability —

• It is made of 3 mm of boiler steel
• High quality of a welding seam (robotic welding);
• Settlement service life of 10 years
• Powder painting;
• Parameters of coppers are confirmed with individual thermodynamic and hydraulic calculations.
• All coppers of Marten Base after welding undergo pressure testing - it is operation at which the copper is put under pressure for 10 - 12 hours.
• Such check guarantees that the solid propellant copper of Marten Base will arrive to the consumer obviously tight and many years will not pass.
• Protection against burns
• This reliable equipment, with efficiency of 76%, calculated on long-term operation.

Reasonable price

1. In Marten Base no, there is nothing superfluous therefore the price is available to all at whom the average income.

Are included in the package of delivery:

• Solid propellant copper;
• Passport;
• Thermometer.

Gift from the SanTehLux company

For all Marten Base which bought a copper

The temperature regulator operates copper power.

By means of closing or opening of the gate of air supply in the combustion chamber

What will the goods give you it?

MARTEN BASE Availability, reliability and durability of MARTEN BASE is a series of available, reliable and convenient coppers which appeared thanks to deep study of requirements of the market and long-term experience of designing and production of coppers.

All these requirements are most considered in the MARTEN BASE models.

You can heat most effectively the house thanks to

• to the increased heat exchanger,
• consisting of a water shirt,
• the water filled grid-irons,
• the massive top water filled shelf and pipes,
• the hot dymogaz which are slowing most down pass to a flue.
• Thanks to such decision we achieved increase in efficiency of the heat exchanger.

Fuel for MARTEN BASE are firewood, coal, briquettes, spill, branches.

The copper of MARTEN BASE is non-volatile and will support heat in the house for 4-5 hours.

After a fuel burn-out the copper of MARTEN BASE is easily cleaned thanks to big doors and the built-in cindery box.

Adjustment of burning is carried out by means of the thermomechanical regulator (in a set it is not delivered).

If necessary an opportunity for installation of the fan of pressurization and the controller is provided.

ADVANTAGES OF MARTEN BASE:

• The increased heat exchanger;
• Non-volatility;
• Protection against burns;
• Existence of a seat under the thermomechanical regulator;
• Big adjustable loading and auditing doors;
• Capacious cindery box;
• Adjustable loops;
• Service life of 10 years;
• Guarantee 3 years;
• Beautiful appearance.

A series of coppers MARTEN BASE are a real opportunity to begin to save already now!

Qualitative material.

Solid propellant Copper of Marten Base are made from heat-resistant, boiler steel, not exacting to quality of fuel.

• Pipes and the water filled, besshevny grid-irons are made of boiler steel of 5 mm
• In coppers of the Marten Base series steel of a teplobenik of 3 mm.
• Brand 09G2S steel - steel which in standards of the EU has marking of P265GH is applied.
• It is boiler steel, service life in the conditions of high temperatures up to 10 years

The high-precision equipment, at production.

• To release a large number of coppers of quality Marten Base it is impossible to do without the modern high-performance equipment. By production of coppers it is used such machines: "Fronius" (Austria), "Hiperterm" (USA)," Euromac" (Italy), "Motoman" (Japan).
• In welding works of Marten Base the robot is used that at all solve a leakage problem.

Step 1

Check

1. All coppers of Marten Base after welding undergo pressure testing - it is operation at which the copper is put under pressure for 10 - 12 hours.
2. Such check guarantees that the solid propellant copper of Marten Base will arrive to the consumer obviously tight many years will not pass.

Step 2

Final assembly of Marten Base.

Painting

• Coverings are painted by method of powder painting on the modern painting line.

• Paint it long does not serve dependent on time of service of a solid propellant copper of Marten Base.

Step 3

Technical control (Quality Department), as in Soviet period.

• The final stage before receipt of a copper of Marten Base on a finished goods warehouse is a passing of technical control (Quality Department).
• At the same time more than 20 parameters, according to the card of control are checked.

All these actions guarantee that the consumer will receive the copper which is conforming to all requirements and not having factory defects

Characteristics and Comparison

Parameters solid propellant copper of Marten Base 18 KW

 

Fire chamber parameters

Depth	mm	570
Volume	l	63
Grid-irons	cooled

Fuller information

Parameter	Measurement unit.	Value
Rated power of a copper	kW	18
Approximately heated area	m ²	180
Fuel main / alternative	anthracite, coals / firewood
Heat exchange surface area in a copper	m ²	1.8
Efficiency, not less	%	76
Duration of combustion of single loading	hour	5-8
Water capacity in a copper	l	47
Copper weight without water	kg	125
Necessary draft of combustion gases	Pas	20-25
Temperature of combustion gases at an exit from a copper	°C	140-220
The recommended minimum water temperature	°C	58
Maximum water temperature	°C	95
Nominal (maximum) pressure of water	MPa (bar)	0.15 (1.5)
Test pressure of water, no more	MPa (bar)	0.15 (1.5)
Electricity consumption, no more	W	—
Diameter of branch pipes of direct and return water	mm	40
Fire chamber size
Depth	mm	570
Volume	dm ³	63
The recommended flue parameters
Cross-sectional area	cm ²	248
Internal diameter	mm	178
Height (minimum admissible)	m	5
D ÷ (x/y)	mm	210/102
Overall dimensions of a copper
B	mm	415
H	mm	753
H1	mm	—
L	mm	640
L1	mm	900

How it is correct to use?

Important guide to use,

To installation of a solid propellant copper Marten Base

1. Group of safety
2. The correct installation according to requirements of the plant
3. Time and temperature of burning
4. Adjustment by means of thermo - mechanical
5. Ash-content, flowability, humidity of fuel.
6. Cleaning of the heat exchanger as it is frequent also what advantage of it
7. Buffer capacity
8. Flue
9. Lack of electricity
10. Video

The first and the Most important.

Group of safety:

1. Manometer
2. Dumping valve
3. Mayevsky's crane.

If the assembler agrees to establish a solid propellant copper without group of safety, know, as he will make all system of heating only for this purpose to take from you money. But what will be then it does not interest.

There is no group of safety there is no stability and long work because any temperature increase in a copper higher than 95 degrees is fraught for a copper with failure. And at worst to explosions.

Save on another but only not on it. Think you need these problems in the winter?

---

The correct installation according to requirements of manufacturer.

Always consider the important guide to installation of a copper Marten Base. Thanks to it you protect yourself from problems with formation of condensate on walls of a copper and from premature failure of the equipment calculated for work up to 15 - 20 years.

Also saving on Marten Base copper binding, to be exact on three running valves, your copper several times will quicker burn firewood or coal. With much smaller efficiency. It means, you will need to run and enclose in the winter much more often.

Read or at least thumb through service a manual from a solid propellant copper of Marten Base giving manufacturer. His not silly people wrote. They provided many standard problems.

Time and temperature of burning

Some think that if to establish burning temperature to 50 C degrees, then they will increase burning time.

But, at which actually the best temperature a solid propellant copper of Marten Base works for the declared 85% of efficiency, it from 65 C degrees and above. Only then on walls of the heat exchanger condensate and respectively pitch will not be formed. The flue will not be hammered and draft of combustion gases will always be top-level.

---

Ash-content, flowability, humidity of fuel.

You should not expect that the solid propellant copper of Marten Marten Base will long burn at one laying of firewood if you have wet firewood, briquettes with a big ash-content and not coal, and dust.

Firewood has to be the driest. At least 20% of humidity. Under other conditions Marten Base copper at first will dry them, and then to heat your house. Moreover remember, the it is more than ash-content in briquettes or humidity in firewood, those will need to remove more dirt from heat exchanger walls.

---

Cleaning of the heat exchanger as it is frequent also what advantage of it.

Important regularly, or as necessary, to bring internal walls of a copper of long burning of Marten Base, into an appropriate look, removing pitch. Remember, only being in pure a state the copper can well heat the water which is in a shirt and in your system of heating.

Only being pure, threw or boiler steel of which the heat exchanger is made will serve long, but will not rust in several years.

Understand, it rusts in this case not from water, and from soot of pitch and condensate which also destroy it.

And here still that tell those who already uses to solid propellant coppers.

Products of burning are postponed on internal walls of a copper and a flue and if to undertake nothing, then it is fraught with the following.

• In the most harmless case, it just decrease in efficiency of heat exchange.
• On heat exchanger pipes in a copper soot and pitches, and warmly accumulates, instead of that to be transferred to the heat carrier in literal sense goes to a pipe.
• The consumption of firewood increases, at the exit from a copper in a flue the sensor shows essential increase in temperature.
• And the copper cannot heat the heat carrier to the set temperature. It is necessary to clean, and it is the procedure not really pleasant and on a pervost (there is no experience yet) occupies rather large number of time (now that I for minutes 20-30 will cope with it). Sometimes when cleaning it is necessary to use serious force.

---

Buffer capacity

1. You want to reduce the number of approaches to a copper within a day and less often to put firewood or coal?
2. You want on to forget always about cleaning of a copper from soot and pitch?
3. You want to get up always in the morning in the warm house?
4. Not to knock from cold teeth rising at night in cold to run to throw coal or firewood?

Establish buffer capacity. A copper heating it will work with the increased efficiency, and then from Buffer capacity your house will be warmed.

---

And in conclusion.

Flue.

Establish a qualitative flue at once. Do not feel sorry for means differently how to be told, penny-wise and pound-foolish.

Only the flue which has two walls and between them a heater, will give you in the winter long and to live quietly. Other option is a punching of a flue from soot and ignition of a flame can be guaranteed to you.

And again words of eyewitnesses:

There is one more, I would even tell extremely dangerous case.

• The flue grows with not burned down burning products, pitches and soot over time and at some point ignites. And this is really dangerous.
• For the first time, when it at me happened a copper a flue in close proximity (a sandwich to an internal and external steel covering, and between them a heater) was heated to is red.
• It was visible even by the light of. At the same time outside (at the exit from a flue) there were natural fireworks.
• Will take care of prevention of it it is extremely necessary, for this purpose it is periodically necessary to clean a flue. Frequency of cleaning at least once in 1,5 months!

---

Sharp switching off of electricity.

You will have with it no problems if you:

1. Established buffer capacity
2. Made system on drift without pump
3. Become tension converter together with the rechargeable battery

In other case you remember this danger of shutdown of the pump and boiling of water in a copper. Seldom happen that coppers blew up but damage can be caused are serious