Currency MDL
Glue for a tile and a stone of Fliesenkleber-BauUnd buy in Chişinău
Buy Glue for a tile and a stone of Fliesenkleber-BauUnd
Glue for a tile and a stone of Fliesenkleber-BauUnd

Glue for a tile and a stone of Fliesenkleber-BauUnd

In stock
Reconfirm the price with seller
Shipping:
Seller
Moldova, Chişinău
(View map)
+373 
Display phones
Description
Glue for a tile and a stone of Fliesenkleber-BauUnd
Scope:
Warm, morozo-, waterproof tsementosoderzhashchy mix with the increased adhesion is intended for laying of a natural stone with a low-fat surface, a ceramic and facing tile on walls and floors. It is used for internal and external works.

Basis and preliminary processing:
Concrete, brick, gypsum cardboard, plaster (has to be single-layer and should not be smoothed down and have thickness not less than 10 mm), etc. can form the basis. To zashkurit waterproof paint, not waterproof to remove. The basis has to be cleared of dust and free particles, the basis has to be equal, dry and firm. If the basis on the basis of plaster, then it is necessary to put TIFENGRUND primer previously!
If plaster plaster, gypsum cardboard, the heated floor or the surface subject to influence of higher humidity forms the basis, without fail KNAUF KLEBER ELAST diluted with water in the ratio 1:3 need to process.

Preparation:
To mix mix with clear water (in the ratio 1 kg: 0,3 l. waters) before education homogeneous (uniform, without lumps) masses manually or by means of a low-reverse mixing nozzle to leave for 10 minutes for swelling and to mix once again. If necessary to regulate a consistence addition of water or mix. Laying is made at a temperature of the basis and the okruzhayeshchy environment not lower than +50 S. Srok of work with mix - about 3 hours.

For use on terraces, in damp rooms, on the heated floors and on open surfaces to mix mix with KNAUF KLEBER ELAST (in the ratio 1 kg: 0,25 l). Gluing a consistence if necessary to correct water addition. In this case operating time with solution makes about 2 hours. The superficial shpaklevaniye of a surface, layer of 3 mm thick is previously full, in the field of a floor provides with such enriched glue water tightness

Operating procedure:
At first to apply glue with the flat party of the gear pallet on the prepared surface, then "to comb" the gear party at an angle 900. To lay a tile on glue and to press an easy roundabout. At education to replace with surfaces of the put layer of glue of a thin crust, a layer of glue.

To carry out seal of seams only when drying glue. Time of laying and adjustment depends on extent of water absorption of the basis and surrounding temperature. When laying a tile in the areas which are exposed to special influence of negative factors it is recommended to apply glue both on the basis, and on a reverse side of a tile. During drying to protect from a frost.

Before laying of a tile on the warmed floor to make its warming up, and in 24 hours prior to works to turn off heating.

Material consumption:
Depending on thickness of the put layer: stepped appearance of 4 mm - 2kg/sq.m, stepped appearance of 6 mm - 3kg/sq.m.

Storage:
To store bags in dry conditions (on wooden pallets).
Period of storage - 6 months.
Contact the seller
Glue for a tile and a stone of Fliesenkleber-BauUnd
Glue for a tile and a stone of Fliesenkleber-BauUnd
for
by the goods
Your message must contain at least 20 symbols. The message must not be more than 2000 symbols.
Obligatory field is not filled
The field is wrongly filled
The field is wrongly filled
Shipping method
Compare0
ClearSelected items: 0